For most Digital Video Recorder DVR timers, you select a specific program on a specific channel, and tell the receiver how often you want to record that program. You can create a manual timer for a locked program without entering the password. However if you do this, when the timer starts, the receiver may display only an error or password-entry menu screen. The program can be a satellite or over-the-air TV program see page for information and instructions on connecting an over-the-air antenna to your receiver.
You can also press the DVR button three times for quick access to the Schedule screen. Select Timers. Select Manual Timer. Select one of the Timer Types see page 64 for more details. When the DVR finds programs listed that meet your search criteria, it will automatically set a timer to record that program. As the Program Guide is updated, DishPASS will continue to find and record newly listed programs or events based upon your search criteria.
Select Timers and then Edit List. Select the timers you wish to delete. Select Delete. A pop-up window asks you to confirm your choice s. Select Yes on the pop-up screen. By enabling this feature, the Electronic Program Guide EPG always will have the most up-to-date information, and your DVR can automatically adjust or create timers accordingly. The SAT mode button will flash the same number of times as the address number for example, three flashes means address 3. Page 86 Chapter 10 Improving Receiver Control Adjusting the Remote Control Antenna Be sure to point the remote control antenna back of the receiver straight up so you can use the remote control from as far away as possible.
Don't let the antenna touch anything. If your UHF Pro Remote Control 2 isn't working well from far away or another room, you may be experiencing interference from objects near your receiver. To prevent such interference, you can install a 10 dB attenuator available from many electronics parts stores. Adding this attenuator will help keep out stray UHF signals, but it will also cut down how far away your remote control can operate the receiver. Press and hold the SAT mode button for three seconds until all four mode buttons are lit.
Enter 00 or In the instructions below, the column on the left contains basic procedures to perform and the column on the right provides any additional information, if applicable. Holding either remote control in your hand may Place both your DISH remote and the cause learning to fail. Page 97 Remote Controls Operating Other Devices After a button has learned a command successfully, repeat step 5 and step 6 until all commands you want have been learned.
Continue Select Continue Press and hold zero System Wizard screen displays to open the System and says the receiver does not Setup is complete Wizard screen recognize the remote Press ZERO 0. When you program the remote to control another receiver, the remote will send out IR signals to the receiver so the line-of- sight to the second receiver must be unobstructed. Press and hold the TV mode button until all mode buttons light up.
While using this feature, both Remote Control 1 and Remote Control 2 for your satellite receiver can control what is displayed on all TVs connected to the system.
With the Archiving feature enabled on your account fees may apply , you can transfer programs from the receiver to your external storage device, and play back programs directly from a connected external drive. To use this feature, make sure you have a phone line connected to the receiver, Caller ID is enabled on your phone line, and that the Caller ID option is selected on your receiver.
Use the following instructions to view and delete numbers from your Caller ID History. However, you can change the way the Program Guide displays on your TV screen.
If an HD local channel is not available, the SD channel is listed. Also, you can display captions when you play back programs recorded on the receiver's integrated DVR Digital Video Recorder , even if you didn't have them turned on at the time the program or event was recorded. An external decoder is required to enjoy this feature. Note: Not all programs or events contain a Dolby Digital sound track.
Your new receiver uses an optical port for outputting digital audio. Select one of the following methods. Note: If you would like to put your receiver in a remote location for example, inside a closet, or a cabinet in another room, etc. Run the channel scan on all applicable remote TVs, if available. Disconnect and reconnect each cable one-by-one, observing what happens to the picture on the TVs. Note: You may be able to use a wireless modem jack.
You can use this connection to order Pay-Per-View programming using your remote control if you are not able to connect a telephone line. It also provides access to additional content not usually available through your satellite TV subscription.
For this installation, always leave your VCR powered on so that the TV can receive satellite programming. Page Chapter 12 Connecting an Over-the-Air Antenna Scanning for Over-the-Air Channels With your over-the-air antenna adjusted for best reception, use these instructions to scan for over-the-air channels on the nearby TV. Even though these tools are quite helpful, it is recommended that you only use them when you are speaking on the phone with a DISH representative.
You may be asked to display these screens when you call DISH. Remember to have an active phone line or broadband Internet connected to your receiver Warning: Running the Check Switch test while is receiving low or no signal will result in incorrect receiver settings and cause you to lose channels. Look in this section for a description of the problem before calling the Customer Service Center.
Any input is appreciated! Jan 4, 32, 27, Fairfax, VA. I upgraded to a H3 and still have my not K since I own it. The install tech claimed I couldn't sell it any longer. I too checked here and people didn't know other than to agree with the tech. I also had two leased 's which the tech captured and said he was trashing.
Jan 10, 2, Charlotte, NC. I recommend contacting retention about the existing customer promotion. This thread Existing Customer Promotion has the phone number. I was able to upgrade to a H3 for free. It does require a 2 yr contract. The promotion locked in the price for 2 years. Reactions: TheKrell and JSheridan.
Sep 7, 19, 30, Phoenix, AZ. TheKrell said:. Click to expand Reactions: TheKrell. Feb 16, 8, 9, USA. NashGuy said:.
Reactions: TheKrell and charlesrshell. Nov 3, 1, 1, Seaside Oregon. JSheridan said:. The promotional price for DirecTV is for the first 12 months of the 24 month contract. After that the price will go up quite a bit.
With that new 24 month Dish contract will come a 24 month price lock also. Can anyone tell me what the penalty is for early termination of a new month contract if we were to take the Hopper upgrade promotion with discount and month price lock? Aug 25, 9, 15, Pekin, IL. Reactions: Howard Simmons , TheKrell , charlesrshell and 1 other person. HipKat said:. They are lying or are just clueless. I have 5 in my own inventory and our warehouse has 2 pallets of them.
T IPS N OTES A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Unplug the receiver power cord by gripping the power plug, not the cord. The power plug must be readily accessible so that the equipment can be easily disconnected from the AC power. This could cause fire or electrical shock. When installing the antenna, take extreme care to avoid touching such power lines or circuits, as contact with them can be fatal. Refer all servicing to authorized service personnel. Excessive shock and vibration can damage the hard drive.
If the receiver is cold to the touch, do not plug it in immediately. Let it sit unplugged at room temperature for at least 45 minutes before plugging it in. During an electrical storm or when the receiver is left unattended and unused for long periods of time, unplug the power cord from the wall outlet, disconnect the lines between the receiver and the antenna, and disconnect the telephone line. This will provide additional protection against damage caused by lightning or power line surges.
On some TVs, the presence of fixed images for extended periods of time may cause them to be permanently imprinted on the screen. You are about to experience the excitement and convenience of our Direct Broadcast Satellite DBS service, which delivers the very best picture and sound quality.
DISH Network consistently provides the latest products and satellite-delivered services—with high performance, ease of operation, and a wide variety of entertainment options.
In addition, an optional over- the-air tuner module is also available. Additionally, the DVR features and a host of other functions make your new receiver one of the most versatile and exciting devices in home entertainment. This satellite receiver lets you decide how you watch TV.
You can record and play back audio and video with full digital quality. You can pause a live program and not miss any of the action, or you can record a program to watch later without a VCR. This section explains how the user guide is divided and the conventions used throughout.
Example : Press SAT. Example : Select the Locks option. If a specific remote control must be used, this guide will refer directly to Remote Control 1 or Remote Control 2. These instructions are numbered left to right as shown in the sample below.
This section describes how to order your packages and provides information on how to find information about your DISH Network account. A representative will explain the available program packages. Give the representative information from the System Information screen, as requested.
This process usually takes just a few minutes. If you want to know about charges to your DISH Network account or if you would like to make changes to your programming packages, be sure to have your account information handy and choose one of the following:. After you have ordered your programming package, you can begin enjoying the features of your new satellite TV receiver. For more about the pause feature of your receiver, see Pausing a Program on page Take this tour to learn how to make basic recordings of your favorite shows.
Catch all the action on Pay-Per-View. Take a break from regular TV and order the latest movies, sports, and special events. For details on ordering Pay-Per-View events, see page Be sure to connect an active phone line to your receiver before you order a Pay-Per-View event see the instructions on page Enjoy movies and other programming any time without schedules, without waiting and without leaving your home.
DishONLINE lets you download movies and other programs to the satellite receiver if it is connected to a broadband high-speed Internet connection. For steps to connect your satellite receiver to the Internet, refer to Connecting a Broadband Internet Connection on page For more information, go to dishnetwork.
Satellite television uses satellites in a stationary orbit over the Earth to deliver television and audio programming. This type of orbit enables the satellites to stay aligned over one place on the surface of the Earth. Once the satellite dish is aimed at the satellite, the dish does not have to move to follow it. Heavy rain, snow, or dense cloud cover can reduce the satellite signal, which may interrupt your programming service.
Your service will return after the weather condition has passed. Aiming the satellite dish to get the strongest signal during installation, will help prevent rain and snow from interrupting the signal. This event occurs during a few days at the beginning of the spring and the beginning of the autumn and lasts only a few minutes. When the sun has moved from behind the satellites, the programs will reappear.
This is an unavoidable natural event and has an adverse effect on many satellite program providers. Your satellite receiver is equipped with a standard telephone jack that you use to connect to an active telephone line.
Keep the receiver connected to an active telephone line so that you will be able to order pay-per-view programs using your remote control, use all of the Dish HOME Interactive TV features, and other services from DISH Network see the instructions on page Your satellite receiver can be connected to your broadband home network. Currently this connection allows you to order additional content not usually available through your satellite subscription, and you can order pay-per-view programs using your remote control if you do not connect a phone line to your receiver.
This feature is included with your receiver to assure you that the connections between your receiver and TV s are not lost, and also provides useful information about your receiver and its features.
Make sure you are using the correct remote for your TV-viewing location see page 12 for details. Refer to page 5. For more information on finding something to watch, see Chapter 3: Finding Programs to Watch. The channels that are red in the Program Guide are those which are not currently in your subscription. These instructions help you improve your remote control settings to best operate your satellite receiver.
To keep this from happening, you can change the remote address. You can also use these instructions to change the address on Remote Control 1. If you wrote down an odd number in step 1, choose an even number; if you wrote down an even number, choose an odd number to enter here.
If you entered the address correctly, SAT will flash three times. Write down the number you entered:. Make sure the Remote Address you see on the System Information screen is the same as the one you entered in step 3. If it isn't, the remote cannot control the receiver.
The SAT mode button will flash the same number of times as the address number for example, three flashes means address 3. If you have two UHF Pro remote controls in your house, ensure one uses an odd-numbered remote address and the other an even-numbered address. Be sure to set the remote control antenna back of the receiver straight up so you can use the remote control from as far away as possible. Don't let the antenna touch anything. If your UHF Pro Remote Control 2 isn't working well from far away, you may be experiencing interference from objects near your receiver.
To improve your remote control's range, try the following:. Do not place an over-the-air antenna on top of your receiver. This is applicable for TV2 in Dual User mode. Unwanted UHF signals may interfere with signals from the remote control to the receiver. To prevent such interference, you can install a 10 dB attenuator available from many consumer electronics parts stores.
Adding this attenuator will help keep out stray UHF signals, but it will also cut down how far away you can use the remote control. You can do this by any of the following procedures:. To change the mode, press the button for the device you want the remote to control. Release the mode button. Set up the remote to control other devices using the device codes listed on page In the instructions below, the column on the left contains the instructions and the column on the right provides additional information.
The mode button flashes.
0コメント